How To Replace RV Flooring With a Raised Slide

How did we replace our RV flooring?  That is a question we’ve received multiple times concerning our RV Remodel.

For materials, we scoured the internet and found that most RVers recommend vinyl flooring sold by Home Depot, Allure Trafficmaster plank flooring to be exact.

We did quite a bit of reading about the product and started to find alarming reviews, like here and here. There were a variety of issues but the most common seemed to be surrounding Home Depot’s lack of customer support for the product and how stinky the flooring was once installed (off-gassing).

Some people said it took months for the smell to go away and that was with open windows.  Since this remodel was done late in the winter, airing wasn’t an option and we sure didn’t have a few months for it to finish off-gassing before we lived in it.

Ugh.

The more we read, the more we became concerned. In the end, we decided to NOT install Allure.

Now in all fairness, I KNOW many RVers use this flooring and have no issues whatsoever.  But we didn’t want to be one of the ones that got a bad batch.

We then looked to our local Lowe’s to see if they had a similar flooring that was not prone to off-gassing issues.  They had something similar, yes, but did it off-gas?  It was possible and we weren’t taking any chances so we settled on the most affordable option out there. Mark installed sheet vinyl.

Is it stylin’ and amazing?! No. but it serves its purpose only cost us about $300 to do our entire camper.  4 months later, we’re very pleased with the flooring. It’s held up well and if for some reason we need to do anything to the subfloor, we can pull up the vinyl and place it back down.  Easy peasy.

Our 96′ Winnie has one large slide over the dining and living area.  Because of the year, it is a raised slide and sits about 3 inches higher, (see crappy picture below).

So how do we properly replace the RV flooring on the slide?

When Mark demo’d the camper he took out the booth dinette and couch and ripped out the carpet in the slide area.  We were a bit apprehensive about dealing with a raised slide but after the fact, Mark would tell you it was very easy to do.

Sheet Vinyl Installed - Replace RV Flooring

Once all the carpet and staples were removed, he simply laid the vinyl down and trimmed it with wood against the wall, and screwed in a metal transition strip along the top at the front of the slide and in the doorways between the bathroom and bedroom.

He had to deal with the front of the slide, which was originally covered with carpet. (see crappy picture below)

How to Replace RV Flooring on a Raised Slide

To cover the front, he bought 1/2″ X 3″ trim boards to cover the 13 feet of length of the slide.

Our son, Eli, was employed in the sanding of the board and Mark stained the wood a dark color.

sanding-trim-piece
Mark wanted to make sure the slide was sealed so he installed 3/4″ weather stripping all along the slide first.  It was screwed right to that metal strip you can in the picture below.  This is the type of weatherstripping that is used on garage doors.

trim-and-transition-for-slide

After the stripping was attached, he screwed on the sanded and stained trim board, and lastly, the metal transition strip was attached to the top outer edge of the slide (and overlaps the front wood trim slightly.

slide-replaced

The Snag

So this all worked great and looked awesome.  But after taking the slide in and putting it back out we ran into a problem that I shared about here.  The front corner of the wood trim snagged the vinyl.  It snagged it good.

rip-in-vinyl-from-slide

Stinkles!

Rather than replace the entire sheet of vinyl, Mark cut out the offending area which was a 1 1/2 foot by 3 1/2 foot area.  He cut some fresh vinyl from the scraps we had and tacked it down with 2-sided carpeting tape.

replaced-section-of-vinyl

In the picture, it is obvious.  But if we didn’t point out to you in the camper, you’d likely never notice the patch job.

To stop the slide from snagging the vinyl again, Mark trimmed about 1/2″ down the length of the front trim pieces

The  Stairwell

The stairwell was previously completely covered in carpet.  In order to get all the adhesive off of the stairs, he had to spray a product (similar to Goo-Gone) and scrap the glue off.

goo-gone-stairwell-of-rv

The walls of the stairwell were painted with an oil-based paint since the material was metal

rustoleum-oil-based-paint-for-rv-stairwell

Lastly, he placed the vinyl on the top of each step and trimmed the edges with a metal transition strip.

That open step is where the batteries are housed.  Once the cover is on, you can see the vinyl on those 2 stairs.

The picture below shows the trim that Mark placed around the outside walls where the vinyl was placed.

And here is a closeup of the finished stairs with all the transition strips in place.

finished-steps

Up until this writing, I’ve not convinced Mark to remove the cab carpeting and recover the doghouse (the engine cover between the 2 front seats).  Truth be told, we don’t even notice the old upholstery/carpet.  Hardly.

Maybe someday, but for now our flooring is complete.

Until next time,

25 thoughts on “How To Replace RV Flooring With a Raised Slide”

  1. Then depending on the size of my transition strip and how it sits on the main flooring, I may have my slide out flooring stop a bit before the edge so that the transition strip can come flush as the slide sinks into the fully out position.

    Reply
  2. Hi Julie, since the original carpet is thicker than your new flooring was there any problem of the slide moving over your new flooring ?

    Reply
  3. Will replacing carpeting with vinyl flooring add more weight to trailer? We’re thinking of using the strip type that looks like wood planks.
    Thank you,
    Joyce d.

    Reply

Leave a Comment